Closed CLOSED

[TwingklingWatermelon]

ASAP po sana kase bigla nalang po nawala ung ram ko eh may roon namn po siyang ram naka salpak namn po at nilgay ko na din po sa slot 2 ganun paden ayaw paden eh
una po may lumalabas po na "A device which does not exist was specified" kapag pinipindot kopo ung Local Disk (F po ata un nalimutan ko na ano name tas bigla nalang po siyan nawala nuong tinary ko ito

• STEP 1. Open up a command window, also make sure that you run it with administrator privileges
• STEP 2. Now Launch Diskaprt Utility using the below command

diskpart

• STEP 3. To see all the disks execute the below command

list disk

• STEP 4. Once you know which disk has to be partitioned, simply execute the below command

select disk 0

• STEP 5. Now completely clean it by the below command

clean

• STEP 6. Now execute the below command just to make sure that the disk is still selected

list disk

• STEP 7. Make the partition Primary by following the below command

create partition primary

• STEP 8. Now select the newly created primary partition

select partition 1

• STEP 9. Activate the partition

active

• STEP 10. Using the below command we will format it with NTFS and assign a label to the partition

format FS=NTFS label=Data quick

• STEP 11. Assign a letter to the partition

assign letter=g

• STEP 12. Finally, exit the disk part

exit

• STEP 13. Hopefully, your issue has been resolved

4. Replace the Hard Disk​

If any of the above methods fail to work then this device cannot start. (code 10) a device which does not exist was specified. windows 10 issues are very critical either contact customer care or you have to replace the hard disk with a new one. There arent any other methods that can help You do not have permission to view the full content of this post. Log in or register now..

files ko h

 

[TwingklingWatermelon]

Huwag muna, yun munang HDD, reseat mo parehong side ng cable, reseat mo din yung power supply cable (yung may wires na red,yellow at black).

anu po ung reseat?

 

[Pen_J]

anu po ung reseat?

Hugutin mo yung cable sa saksakan, inspection kung may defect o dumi ang terminal o connector pins tapos isaksak uli. Shutdown muna syempre bago mag disconnect ng cable.
Ilipat mo rin sa ibang SATA port yung cable, baka nandoon ang problema sa saksakan sa motherboard, pwede mong isaksak sa SATA port no. 2 o no. 4.

 

[pautang1]

ok po

 

[TwingklingWatermelon]

Hugutin mo yung cable sa saksakan, inspection kung may defect o dumi ang terminal o connector pins tapos isaksak uli. Shutdown muna syempre bago mag disconnect ng cable.
Ilipat mo rin sa ibang SATA port yung cable, baka nandoon ang problema sa saksakan sa motherboard, pwede mong isaksak sa SATA port no. 2 o no. 4.

baka po ung SATA may problema kase naka lobo po siya eh

 

[Pen_J]

baka po ung SATA may problema kase naka lobo po siya eh

Ano yung naka-lobo, yung SATA cable? Yung saksakan sa motherboard? Pwede pa-picture? Ganito yung SATA cable at SATA power cable:

 

[TwingklingWatermelon]

Ano yung naka-lobo, yung SATA cable? Yung saksakan sa motherboard? Pwede pa-picture? Ganito yung SATA cable at SATA power cable:

View attachment 2149805View attachment 2149807

opo ung ganyan ung color black po sa second pic nya is lobo po ung dulo nya mamaya po sent ko dito

 

[TwingklingWatermelon]

Ano yung naka-lobo, yung SATA cable? Yung saksakan sa motherboard? Pwede pa-picture? Ganito yung SATA cable at SATA power cable:

View attachment 2149805View attachment 2149807

boss ito napo update inilipat ko po ung SATA 1 ng HDD ko sa SATA 3

yan po ung mga disk ko ung PRIVATE RAN po NVM nalang po dyan kopo kase nilalagay mga RAN PRIVATE na nadl ko

 

[Pen_J]

boss ito napo update inilipat ko po ung SATA 1 ng HDD ko sa SATA 3 View attachment 2150626yan po ung mga disk ko ung PRIVATE RAN po NVM nalang po dyan kopo kase nilalagay mga RAN PRIVATE na nadl koView attachment 2150627

So, linawin ko lang, yung dating Disk 1 ay may unallocated space na 5.1 Gb, pi-nartition mo siya at ito na ngayon yung G: drive na Private Ran.
Ngayon yung NVM mo (SSD = Ramsta) ay naging Disk 0 na dahil ang connection niya ay mas mataas ang priority (SATA 1? o SATA 2?) kaysa sa SATA 3 kung saan naka-konekta si HDD.
Ok, Disk 1 na ngayon yung description ng HDD.

Anyway, sa Disk Management, right click mo yung Disk 1 tapos screenshot mo, check ko yung mga available na options.
Tapos open mo si Device Manager, expand mo yung Disk Drives at pa-screenshot din.
Next, Show hidden devices, scroll down ka at expand mo yung Storage volumes, pa-screenshot uli. Check ko kung sumisilip na si HDD (ST500DM0002-1BD142).

 

[TwingklingWatermelon]

THIS THREAD HAS BEEN CLOSED MY HDD WAS DAMAGE AFTER LONG WAIT AND NOW I GIVE MY HDD TO THE SHOP WHEN I BOUGHT IT AND SAID TO ME HE NEED TO PULL OUT MY HDD I USE MY WARRANTY SO I HAVE 2WEEKS TO WAIT.. THANKS TO THE MAN HELPING ME HERE !!