PLDT Boosteven R281 (Band Locking)

[L E N A R]

di gumagana yung add CA sakin ang malas haha isang band lang nagllock

siguro wala nung isang band na ni lock mo

 

[_ameee]

siguro wala nung isang band na ni lock mo

may signal naman po both

 

[H4wk3ye]

may signal naman po both

If i'm not mistaken you cant lock CA.

 

[Pr3st1ge]

Thank You!
Edit: the pass is incorrect

Help, password still incorrect

 

[-M I A Z H E R-]

Help, password still incorrect

Password is : YøùTùbéContent

 

[Pr3st1ge]

Password is : Y⊕ùTùbéContent

 

[oblivion85]

Wow, maraming salamat po dito, malaking tulong ito.

Pa try po pala sa iba baka heto yung acs server ng pldt, pag click ng software update dun sa old nginx config and inspect element, console resources heto yun piniping na address:

You do not have permission to view the full content of this post. Log in or register now. ---

So triny ko i block yung ip address dun sa built in ip filter ng router sana mag work. Pa try nalang sa iba baka maging successful pag block ng auto update in the future.

 

[oblivion85]

Y and C lang po capital.

 

[Pr3st1ge]

Y and C lang po capital.

Problem Solve Thanks!

 

[Pr3st1ge]

Pls help, Tried to lock band 1 by using command AT*CELL=1,3,3,150, after that says "OK" then this happen, I can't go to default when I try AT*CELL=0, "ERROR" said and I'm stock in red light,pls help

 

[_ameee]

Pls help, Tried to lock band 1 by using command AT*CELL=1,3,3,150, after that says "OK" then this happen, I can't go to default when I try AT*CELL=0, "ERROR" said and I'm stock in red light,pls helpView attachment 1585577View attachment 1585581

same, sumobra ng 0 sakin and nabrick yata. wont revert back to normal kahit i reset

 

[H4wk3ye]

Try to change mode to 0 if it is ok then try to perform frequency lock again.

 

[L E N A R]

same, sumobra ng 0 sakin and nabrick yata. wont revert back to normal kahit i reset

hard reset mo yung button dun sa likod

 

[H4wk3ye]

same, sumobra ng 0 sakin and nabrick yata. wont revert back to normal kahit i reset

Try to change mode to 0 if it is ok then try to perform frequency lock again.

 

[H4wk3ye]

Try to change mode to 0 if it is ok then try to perform frequency lock again.

Ex: AT*CELL=0,3,3,150

 

[Pr3st1ge]

Try to change mode to 0 if it is ok then try to perform frequency lock again.

Tried AT*CELL=0 shows "error"
Also, signal LED flash for a minute then goes off

 

[_ameee]

hard reset mo yung button dun sa likod

negative master

 

[H4wk3ye]

Tried AT*CELL=0 shows "error"
Also, signal LED flash for a minute then goes off

AT*CELL=0,3,3,150,122 try to run this Lods mamaya try ko yang new tricks.

 

[_ameee]

ingat nalang lods na wag magkamali sa code

 

[Pr3st1ge]

AT*CELL=0,3,3,150,122 try to run this Lods mamaya try ko yang new tricks.

Not working, Still Error