Ang itry mo yung dual wan nya, isaksak mo sa WAN/LAN1 ang isa pang internet source tapos check mo internet speed, matic mag cocombine or load balance ang LTE/WAN nyan, tapos hugutin mo ang WAN/LAN1, stable parin ang ping naka failover narin ang config nyan. Kung sa LTE mo naman susubukan ang failover try mo iconnect WAN/LAN1 tapos mag change bands ka, goods parin ang ping.
Naka preconfig na ang Dual WAN, Fail Over at Load Balance nyan.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286r-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
tapos pwede mo na iscp ung firmware
Code:
STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
para sa bandlocking - You do not have permission to view the full content of this post.Log in or register now.
pwede ka na maginstall ng mwan3 at iconfigure.
kayo na bahala sa unlock
AT+ZNCK="nckcode" via /dev/ttyACM0
may band 28 ang s12 ρrø and openwrt ang firmware ng s12 ρrø. iba lang libc na gamit kaya di ka directly makakainstall from openwrt repo unless install mo musl.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286r-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
tapos pwede mo na iscp ung firmware
Code:
STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
para sa bandlocking - You do not have permission to view the full content of this post.Log in or register now.
pwede ka na maginstall ng mwan3 at iconfigure.
kayo na bahala sa unlock
AT+ZNCK="nckcode" via /dev/ttyACM0
in addition pala dito. pag nasa stock fw ka, pwede mo maaccess root shell ng lte module (pxa1826) using adb shell
kayo na bahala maghanap kung maunlock niyo via that. di naman importante sakin ung unlock.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286r-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
tapos pwede mo na iscp ung firmware
Code:
STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286r-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
para sa bandlocking - You do not have permission to view the full content of this post.Log in or register now.
pwede ka na maginstall ng mwan3 at iconfigure.
kayo na bahala sa unlock
AT+ZNCK="nckcode" via /dev/ttyACM0
in addition pala dito. pag nasa stock fw ka, pwede mo maaccess root shell ng lte module (pxa1826) using adb shell
kayo na bahala maghanap kung maunlock niyo via that. di naman importante sakin ung unlock.
hello sino pwede help sakin newbie lang po ako sa open vpn sa modem
pano po ba ilagay yun config sa modem nag fafatal error po kasi e may babaguhin paba don ang ginawa ko po kasi is upload ko lang then click enable and start anyway ang modem kopo zte mf286ra openwrt
hello sino pwede help sakin newbie lang po ako sa open vpn sa modem
pano po ba ilagay yun config sa modem nag fafatal error po kasi e may babaguhin paba don ang ginawa ko po kasi is upload ko lang then click enable and start anyway ang modem kopo zte mf286ra openwrt
gamitin mo ung 22.03 rc instead of snapshot You do not have permission to view the full content of this post.Log in or register now.
panget gumamit ng snapshot pag di mo alam ginagawa mo.
dapat nakaplug na uart mo. tapos ion mo ung router. lalabas dun un countdown. bago matapos press a key.
gamitin mo ung 22.03 rc instead of snapshot You do not have permission to view the full content of this post.Log in or register now.
panget gumamit ng snapshot pag di mo alam ginagawa mo.