MF286RA openwrt.

[zer09yn]

Sinu po nakasubok na Nito?
Openwrt for ZTE MF286RA

You do not have permission to view the full content of this post. Log in or register now.


You do not have permission to view the full content of this post. Log in or register now.
Guide

 

[zer09yn]

Install Instructions:​

Serial + initramfs:​

1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to You do not have permission to view the full content of this post. Log in or register now..
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:setenv serverip 192.168.1.3
   setenv ipaddr 192.168.1.72
   set fdt_high 0x85000000
   tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
   bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to stock.
6. Login via ssh or serial and remove stock partitions:ubiattach -m 9 #it could return error if ubi was attached before or rootfs part was erased before
   ubirmvol /dev/ubi0 -N ubi_rootfs #it could return error if rootfs part was erased before
   ubirmvol /dev/ubi0 -N ubi_rootfs_data #some devices doesn't have it
7. Install image via “sysupgrade -n” (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf286d-squashfs-sysupgrade.bin”; previously wgeting bin). Sometimes it could print ubi attach error, but please ignore it if process goes forward

 

[marukoy]

Install Instructions:​

Serial + initramfs:​

1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to You do not have permission to view the full content of this post. Log in or register now..
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:setenv serverip 192.168.1.3
   setenv ipaddr 192.168.1.72
   set fdt_high 0x85000000
   tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
   bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to stock.
6. Login via ssh or serial and remove stock partitions:ubiattach -m 9 #it could return error if ubi was attached before or rootfs part was erased before
   ubirmvol /dev/ubi0 -N ubi_rootfs #it could return error if rootfs part was erased before
   ubirmvol /dev/ubi0 -N ubi_rootfs_data #some devices doesn't have it
7. Install image via “sysupgrade -n” (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf286d-squashfs-sysupgrade.bin”; previously wgeting bin). Sometimes it could print ubi attach error, but please ignore it if process goes forward

may link ka ng source? basahin ko lang.

 

[aldrinmeh]

Paano kayak via serial

 

[Frwa]

Bookmark to palang sir. Diko po pala basta basta maiinstall openwrt sa mf286ra bos. Sana malagyan ito ng video

 

[dwakjbnd]

wala pang wiki entry para sa mf286r/a pero andito instructions na di need ng tftp

You do not have permission to view the full content of this post. Log in or register now.
gumagana rin lte. may exploit para di na need ng serial

 

[lorenda]

support lods....salamat....

 

[zer09yn]

You do not have permission to view the full content of this post. Log in or register now.


Ito yong guide

may link ka ng source? basahin ko lang.

You do not have permission to view the full content of this post. Log in or register now. yan yong guide para sa mf286ra

 

[_ameee]

open yata agad yung yung ssh ng ztemf

hindi pala

pero sure merong exploit yung zte na to di ko lang napansin kung pano ginawa no need serial

 

[dwakjbnd]

open yata agad yung yung ssh ng ztemf

hindi pala

pero sure merong exploit yung zte na to di ko lang napansin kung pano ginawa no need serial

nandun sa link na sinend ko. may exploit to enable telnet gamit firewall rules.

 

[_ameee]

nandun sa link na sinend ko. may exploit to enable telnet gamit firewall rules.

not working kakatry ko lang

yung method 2 baka working since ssh yata ang ginamit non hindi telnet so baka wala ngang compiled busybox

 

[pspx010]

Eto kaya nakita ko lang din

You do not have permission to view the full content of this post. Log in or register now.

Eto kaya nakita ko lang din

You do not have permission to view the full content of this post. Log in or register now.

May nakapag enable na kaya telnet nito for change imei?

 

[dwakjbnd]

not working kakatry ko lang

yung method 2 baka working since ssh yata ang ginamit non hindi telnet so baka wala ngang compiled busybox

nope. method 2 basically downloads busybox to your modem.

tapos parang method 1 narin.

 

[pspx010]

Eto pa nakita ko lang din.
Bka makatulong.

https://github.com/paulo-correia/ZTE_API_and_häçk

 

[JohnK1LL]

up

 

[dwakjbnd]

Eto pa nakita ko lang din.
Bka makatulong.

You do not have permission to view the full content of this post. Log in or register now.

nope. wala jan ung method 2. may nag try na ng method 1 so hindi yan gagana.
nasa commit message nung link na sinend ko ung instructions. try nyo method 2 sa gaining root access.
if wala, need to disassemble for uart pins.

 

[pspx010]

nope. wala jan ung method 2. may nag try na ng method 1 so hindi yan gagana.
nasa commit message nung link na sinend ko ung instructions. try nyo method 2 sa gaining root access.
if wala, need to disassemble for uart pins.

Un lang. Mukhang may bago nanamang pagkakaabalahan hehe. Cge biss salamat sa info.

 

[pspx010]

nope. wala jan ung method 2. may nag try na ng method 1 so hindi yan gagana.
nasa commit message nung link na sinend ko ung instructions. try nyo method 2 sa gaining root access.
if wala, need to disassemble for uart pins.

Negative sir hindi din gumana ung method 2.

 

[dwakjbnd]

Negative sir hindi din gumana ung method 2.

get a uart cable then haha.

 

[pspx010]

get a uart cable then haha.

Hehe, meron narin akong abang na uart kaso tinatamad pako magbaklas at maghinang. Sana merong mas madaling way... Itago ko muna ung mf ko. Thanks sa info sir.