Help Converge router swap

[broadmlnd]

Good day, ask ko lang yung converge router ko sa bahay luma, naka 2.4ghz wifi lang siya and sa kapatid ko 2.4&5ghz supported pero putol na yung linya nia. Pwede ko ba gamitin yung router nia sa active subscription ko ng walang pinapalitang settings? Nagtanong ako sa converge kailangan magbayad para sa router upgrade eh. TIA

 

[-Hexacode]

Hindi pwede idol kasi naka config nayang router mo sa server nila, unless gagawin mo nlang extension yang router ng kapatid mo gagana yan

 

[Phc-Joshua]

I think, gamitin mo nalang yung router for extension/repeater.
Kasi fiber yan eh, naka config yan sa System nila. Kapag pinalitan mo need mo din magsabi sa kanila.

 

[whateve12]

tinesting ko un boss kaso nd gumana

 

[p4up4u]

gawin mo nalang extension router yang spare mo. tapos turn off mo nalang wifi don sa current router mo.

 

[ceejayramos]

Di pwede, registered sa OLT (Optical Line Terminal) at linked sa account ni subscriber ang serial number at mac address ng dinedeploy nilang ONU/ONT (Optical Network Unit/Optical Network Terminal).
So unless ma-clone mo ang serial number at mac address ng current ONU/ONT mo papunta sa ibang ONU/ONT, hindi yan marerecognize ng system so hindi yan magsi-sync, stuck lang yan sa O3 status (serial number state, waiting for ID/authentication), which of course will not give you any internet connection.

What you can do is buy a mid to high-end router, then request to Converge na i-bridge mode ang ONU/ONT mo. This way, si mid to high-end router mo na ang magiging main router mo. SIya na ang in-charge sa DHCP, WiFi broadcast, firewall, and others. At si Converge ONU/ONT ay magiging modem na lang at wala na siyang routing capability.

In other words, hindi mo pa rin maaalis sa setup si Converge ONT/ONU.

LAN 1 port of Converge ONT/ONU (bridge mode) ===> LAN cable (Cat5e and above) ===> WAN port of mid to high-end router ===> clients (either wireless or wired)

 

[King_Conor]

Di pwede, registered sa OLT (Optical Line Terminal) at linked sa account ni subscriber ang serial number at mac address ng dinedeploy nilang ONU/ONT (Optical Network Unit/Optical Network Terminal).
So unless ma-clone mo ang serial number at mac address ng current ONU/ONT mo papunta sa ibang ONU/ONT, hindi yan marerecognize ng system so hindi yan magsi-sync, stuck lang yan sa O3 status (serial number state, waiting for ID/authentication), which of course will not give you any internet connection.

What you can do is buy a mid to high-end router, then request to Converge na i-bridge mode ang ONU/ONT mo. This way, si mid to high-end router mo na ang magiging main router mo. SIya na ang in-charge sa DHCP, WiFi broadcast, firewall, and others. At si Converge ONU/ONT ay magiging modem na lang at wala na siyang routing capability.

In other words, hindi mo pa rin maaalis sa setup si Converge ONT/ONU.

LAN 1 port of Converge ONT/ONU (bridge mode) ===> LAN cable (Cat5e and above) ===> WAN port of mid to high-end router ===> clients (either wireless or wired)

Bale possible po na i-switch si other router as long as connected parin si converge router? Need lang po itawag sa CS?

 

[ceejayramos]

Bale possible po na i-switch si other router as long as connected parin si converge router? Need lang po itawag sa CS?

What do you mean by switch? Magrerequest ka ng replacement?

 

[burhercate]

Magrequest ka pa rin ng replacement kase libre upgrade to WiFi 5 ONT base sa mga comments sa FB group ng Converge. Yung WiFi 6 ONT yung may bayad.

 

[PHC-Haku]

Ibridge mo nlng or gawin mong AP ung router mo