Closed How to debrand/openline with full admin access (936)

[PHC_Mentos]

HOW TO DEBRAND/OPENLINE WITH FULL ADMIN ACCESS (936)

REQUIREMENTS:

936 MODEM
USB MALE TO MALE
POWER CABLE AND ADAPTER
COMPUTER/DESKTOP/LAPTOP
HUAWEI FIRMWARE You do not have permission to view the full content of this post. Log in or register now.
S22 FIRMWARE/UNIVERSAL
You do not have permission to view the full content of this post. Log in or register now.

MULTICAST UPGRADE TOOL
You do not have permission to view the full content of this post. Log in or register now.

CID READER/COMMANDER

You do not have permission to view the full content of this post. Log in or register now.

HUAWEI DRIVER

You do not have permission to view the full content of this post. Log in or register now.

***Bago po mag START, open mo muna si Huawei Driver, MAG SISILENT INSTALL PO YAN, wala po kau makikita, then proceed to GREEN MODE PHASE.

i.GREEN MODE PHASE:
1. OPEN MULTICAST UPGRADE TOOL> Choose UNIVERSAL FIRMWARE<Choose Your LAN Card> CLICK START
2.I-SALPAK si LAN CABLE, then si POWER CABLE. WAIT MO MAG STEADY RED YUNG MODEM MO. then CLICK STOP AND HUGUTIN SI LAN CABLE.

3. HOLD WPS AND POWER (nasa taas ng modem mo) hanggang POWER NLNG ANG NKA ON, then release. WAIT MO nmn mag GREEN YUNG MODEM LED MO... (READY NA ANG MODEM MO TO ACCEPT CODES)

ii.OPENLINE PHASE
1. Salpak mo si USB MALE to MALE SA PC MO AT SA LIKOD NG MODEM .
2. Makikita mo yung Bottom Right Side ng Computer mo NAG IINSTALL NG HUAWEI DRIVER.WAIT MO MATAPOS
3.Since Successfully installed na yung Huawei Driver, OPEN Cid Reader at PILIIN MO yung pinakababang COM PORT.
ICOPY AT I-PASTE ANG MGA CODES NA ITO (pa isa isa lang po)

Unang code:
at ^ nvwrex = 8268,0,12,1,0,0,0,2,0,0,0, a, 0,0,0
Pangalawang code:
AT ^ SYSCFGEX = "00", 3FFFFFFF, 1,2,800C5 ,,
angatlong code:
AT ^ SYSCFGEX = "0302", 400000,1,2,800C5 ,,
(huwag e edit po and command...
KAPAG NAG SUCCESS YANG 3 CODES. OPENLINE NA MODEM MO.....

iii. FULL ADMIN PHASE

1.ULITIN MO ANG GREEN MODE PHASE.
2.ULITIN ANG OPENLINE PHASE pero ito ang gamiting CODES:
AT^SFM=1
AT^RESET
Mapapansin niyo after ng AT^RESET power light nalang po ang iilaw isetup po yung ipv4 settings ng lan
IP= 192.168.1.100
Subnet Mask= 255.255.255.0
Gateway= 192.168.1.1
Preferred DNS= 192.168.1.1 yung sa baba secondary blank na then ok
Pagkasetup po ng ip tanggalin adaptor at usb male to male cable sa pc
4. BACK TO MULTICAST TAYO pero at this time, HUAWEI FIRMWARE na ang gagamitin,
WAIT MO LANG YUNG MODEM MO MAG AUTOMATIC GREEN (no need to HOLD WPS+POWER)

5. KAPAG NAG GREEN NA, OPEN MO SI CiD READER
then input mo ang commands na ito

AT^SFM=0
AT^RESET

Set na ipv4 settings ng lan sa automatic obtain automatically pati dns tapos login ka na sa GUI 192.168.8.1
ID: admin
pass: admin

LASTLY, PUNTA KA SA SETTINGS NG GUI AND CLICK RESTORE DEFAULT SETTINGS..

CONGRATULATIONS! FULL ADMIN NA ANG 936 MO

 

[ultimas palavras]

up , thanks ts

 

[Aries]

Thanks ts keep sharing!

 

[PHC_Mentos]

welcome papsy

 

[Yukki Senno]

Thanks keep on sharing sir

 

[T_TNinsadxzT_T]

Salamat TS keep on sharing

T_TNinsadxzT_T
[sigpic]561669[/sigpic]

 

[PHC Emilia]

Thenks

 

[jessica73]

Advantage of full admin access?

 

[PHC rines88]

wprking po ba?

 

[Bootz_23]

Salamat sa info boss

 

[PHC rines88]

thanks dito ts... full admin na ako..

 

[4keys]

keep sharing

 

[Lucas29]

Thanks for sharing tol. sana with video.

 

[PHC_Mentos]

Kaya nyo yan, Step by Step mga pogi.. PA like naman para ganahan

 

[sweepstakes]

Kaya nyo yan, Step by Step mga pogi.. PA like naman para ganahan

Sir applicable po ba to sa any firmware?

 

[jadejacusalem]

kahit anong diin ko sa power+wps ayaw pa din mag green? may other way paba?

 

[Piyok]

pwede ba to sa november firmware ts?

 

[sweepstakes]

pwede ba to sa november firmware ts?

Sir bago lang po kasi ako sa ganito, may I ask kung ano mangyayari if mali firmware mo.

 

[CHESTER060388]

ty

 

[CHESTER060388]

ty